| To program a welding cobot, secure the part in a fixture, guide the arm by hand or with a tablet to the start and end of each weld, set the welding parameters for the joint, run a test weld, and save the program. Most welders can learn the basics in a few hours because no coding is required. |
The idea of programming a robot sounds intimidating, and for traditional industrial robots it often is. Welding cobots were designed to change that. Many are taught the same way you would show a new apprentice a weld, by moving the torch along the joint while the machine remembers the path.
This guide explains how welding cobot programming works. You will see the common programming methods, how to prepare a repeatable setup, a step by step walkthrough of programming a first weld, how to set the parameters, and the mistakes that trip up first time users.
Do You Need to Know How to Code?
No. Most welding cobots are programmed without writing code. The interface is built around the things a welder already understands, such as where the weld starts, where it ends, what angle the torch should hold, and what settings the arc needs. Programming becomes a matter of teaching the robot those details instead of typing instructions.
That is also why welding knowledge matters more than computer skill. A cobot will repeat whatever it is taught, good or bad. A person who understands torch angle, travel speed, and joint prep will program better welds than someone who only knows the software.
The Three Common Ways to Program a Welding Cobot
Different systems offer different options, and many offer more than one. These are the three methods you will see most often.
| Method | How It Works | Best For |
|---|---|---|
| Drag and teach (hand guiding) | The operator physically moves the arm and records points along the weld path | Short and curved welds, quick learning, first time users |
| Tablet or pendant waypoint programming | The operator jogs the arm with on screen controls and picks weld types from menus | Precise positioning and repeat programs |
| Offline or CAD based programming | Weld paths are created on a computer from the part model before the robot is used | Large part families and planned production |
Before You Program: Set Up for Repeatability
A good program starts with a good setup. If the part sits in a slightly different place each time, even a perfect program will produce uneven welds. Spend time on the physical setup first.
• Fixture the part: Clamp it so it lands in the same position every cycle. This is the single biggest factor in cobot welding quality.
• Check the torch setup: Confirm the tip, nozzle, and contact tip are in good condition and the wire stick out is consistent.
• Calibrate the tool point: The robot needs to know exactly where the tip of the torch is. Follow the manufacturer procedure after any torch change.
• Route the cables: Make sure the torch cable and wire feed can move freely without snagging along the whole path.
• Confirm gas and wire: Check shielding gas flow and wire type so test welds reflect real production.
Setting Welding Parameters
The parameters are what turn a path into a good weld. They usually include wire feed speed, voltage or current, travel speed, and any weaving pattern for wider joints. Many power sources offer a one knob setting that matches voltage to wire speed, which makes the first setup simpler.
Start with the recommended settings for your material and thickness, then adjust based on test welds. Our article on why welding parameters are crucial for high quality welds explains how each setting affects penetration, bead shape, and heat input. Once a program works, the settings are saved with it, so every future run repeats the same recipe.
Also pay attention to the start and the end of each weld. Many programs include a short delay at the start so the arc stabilizes and a crater fill at the end so the weld finishes cleanly instead of leaving a dip.
Using Touch Sensing and Seam Tracking
Real parts are never perfectly identical. Some cobot systems include touch sensing, where the wire briefly touches the part to find the true joint position, or seam tracking that follows the joint during the weld. These features let the robot correct for small differences in part position and gap.
They are optional on many systems, but they are worth considering if your parts vary or your fixturing is hard to make exact. Sensing adds some cost and a little cycle time, in return for more consistent welds.
Testing, Adjusting, and Saving Programs
Never send a new program straight into production. Run it on scrap first, inspect the weld for penetration, shape, and spatter, and then check the path from several angles. Adjust one thing at a time so you know what caused each change.
Once the program is good, save it with a clear name and note the fixture, torch, wire, and gas used. A well organized library of saved programs is one of the biggest long term benefits of a cobot, because each job becomes easy to repeat later.
Tips That Save Time
• Start simple: Begin with short, straight fillet welds before you try complex shapes.
• Reuse what works: Copy an existing program for similar parts and change only what is different.
• Keep notes: Record the parameters and fixture details with each program.
• Check the data: Track arc on time and defects so you can see what is improving.
• Let the welder lead: The best programs come from someone who knows how the weld should look.
Common Programming Mistakes
• Skipping the fixture: Loose or inconsistent clamping causes more bad welds than any software error.
• Poor torch angle: A bad angle taught once is repeated every cycle, so check it carefully.
• Forgetting the tool calibration: After a torch change, an uncalibrated tool point puts the weld in the wrong place.
• No safe approach and retract points: The arm can strike the part or fixture on the way in or out.
• Changing too much at once: Adjusting several settings together makes it impossible to find the cause of a problem.
Training Your Team
Training time for a cobot is short compared with a traditional robot, often measured in hours for the basics. Plan for a little more time to build confidence with parameters, sensing, and troubleshooting. Pairing an experienced welder with the cobot works well, since they know what a good weld looks like. For ideas on shortening the learning curve, see our article on ways to reduce new welder training time.
SEC Automation offers cobot welding as part of its automated welding services, including help with setup and training. When you are ready for hands-on help, request a cobot welding consultation and our team will walk through it with you.
| FREQUENTLY ASKED QUESTIONS |
▸ How do you program a welding cobot?
Fixture the part, guide the arm by hand or with a tablet to record the approach, start, path, and retract points, set the welding parameters, run a test weld, adjust, and save the program for future use.
▸ Do you need coding skills to program a welding cobot?
No. Most welding cobots use hand guiding or visual menus, so no coding is required. Welding knowledge matters more than software skill.
▸ How long does it take to learn cobot welding programming?
Most welders can learn the basics in a few hours, although building confidence with parameters, sensing, and troubleshooting takes more practice.
▸ What is drag and teach in cobot welding?
Drag and teach, also called hand guiding, lets an operator physically move the cobot arm along the weld path while the system records the points, so the robot can repeat the path automatically.
▸ Can a welding cobot handle parts that are slightly different each time?
Yes, if it has touch sensing or seam tracking and the parts are fitted reasonably well. These features let the robot correct for small differences in position and gap.